Josh-Daniel S. Davis (joshdavis) wrote,
Josh-Daniel S. Davis
joshdavis

netbooting p630 woes


Ok, so the ameslab ppc64 2.6 kernels work. The 2.4 kernels show they failed the build. There's an initrd image with, of course, a suse image tacked onto it.

I'm trying to get it to boot to a debian initrd image.

here's the kernel output.

BOOTP S = 1 
FILE: vmlinuz
Load Addr=0x4000 Max Size=0xfffc000 
FINAL Packet Count = 6954 
FINAL File Size = 3560272 bytes.

Elapsed time since release of system processors: 11926 mins 45 secs
zImage starting: loaded at 0x400000
gunzipping (0x3a00000 <- 0x407000:0x6f9632)...done 9369210 bytes
59436 bytes of heap consumed, max in use 41540
Looking for displays
OF stdout is    : /vdevice/vty@0
found display   : /pci@400000000111/pci@2/pci@1/display@0
Opening displays...
opening display : /pci@400000000111/pci@2/pci@1/display@0... done
Hypertas detected, assuming LPAR !
instantiating rtas at 0x000000000fd3c000... done
0000000000000000 : booting  cpu /cpus/PowerPC,POWER4@2
Calling quiesce ...
returning from prom_init
firmware_features = 0xd7f
Starting Linux PPC64 2.6.7-rc2-ames
-----------------------------------------------------
naca                          = 0xc000000000004000
naca->pftSize                 = 0x19
naca->debug_switch            = 0x0
naca->interrupt_controller    = 0x2
systemcfg                     = 0xc000000000005000
systemcfg->processorCount     = 0x1
systemcfg->physicalMemorySize = 0x60000000
systemcfg->dCacheL1LineSize   = 0x80
systemcfg->iCacheL1LineSize   = 0x80
htab_data.htab                = 0x0000000000000000
htab_data.num_ptegs           = 0x40000
-----------------------------------------------------
[boot]0100 MM Init
[boot]0100 MM Init Done
idle = default_idle
Linux version 2.6.7-rc2-ames (jeremy@superego) (gcc version 3.2.4 20030811) #1 S
MP Mon May 31 16:02:05 EST 2004
[boot]0012 Setup Arch
No ramdisk, default root is /dev/sda2
Boot arguments: initrd=init26
EEH: PCI Enhanced I/O Error Handling Enabled
PPC64 nvram contains 16384 bytes
Top of RAM: 0x60000000, Total RAM: 0x60000000
Memory hole size: 0MB
On node 0 totalpages: 393216
  DMA zone: 393216 pages, LIFO batch:16
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: initrd=init26
[boot]0020 XICS Init
[boot]0021 XICS Done
PID hash table entries: 16 (order 4: 256 bytes)
time_init: decrementer frequency = 181.698853 MHz
time_init: processor frequency   = 1453.590824 MHz
firmware_features = 0xd7f
Starting Linux PPC64 2.6.7-rc2-ames
-----------------------------------------------------
naca                          = 0xc000000000004000
naca->pftSize                 = 0x19
naca->debug_switch            = 0x0
naca->interrupt_controller    = 0x2
systemcfg                     = 0xc000000000005000
systemcfg->processorCount     = 0x1
systemcfg->physicalMemorySize = 0x60000000
systemcfg->dCacheL1LineSize   = 0x80
systemcfg->iCacheL1LineSize   = 0x80
htab_data.htab                = 0x0000000000000000
htab_data.num_ptegs           = 0x40000
-----------------------------------------------------
[boot]0100 MM Init
[boot]0100 MM Init Done
idle = default_idle
Linux version 2.6.7-rc2-ames (jeremy@superego) (gcc version 3.2.4 20030811) #1 S
MP Mon May 31 16:02:05 EST 2004
[boot]0012 Setup Arch
No ramdisk, default root is /dev/sda2
Boot arguments: initrd=init26
EEH: PCI Enhanced I/O Error Handling Enabled
PPC64 nvram contains 16384 bytes
Top of RAM: 0x60000000, Total RAM: 0x60000000
Memory hole size: 0MB
On node 0 totalpages: 393216
  DMA zone: 393216 pages, LIFO batch:16
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
[boot]0015 Setup Done
Built 1 zonelists
Kernel command line: initrd=init26
[boot]0020 XICS Init
[boot]0021 XICS Done
PID hash table entries: 16 (order 4: 256 bytes)
time_init: decrementer frequency = 181.698853 MHz
time_init: processor frequency   = 1453.590824 MHz
Console: colour dummy device 80x25
Memory: 1539008k available (4268k kernel code, 3516k data, 204k init) [c00000000
0000000,c000000060000000]
Calibrating delay loop... 362.49 BogoMIPS
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
Brought up 1 CPUs
NET: Registered protocol family 16
PCI: Probing PCI hardware
Using INTC for W82c105 IDE controller.
IOMMU table initialized, virtual merging disabled
ISA bridge at 0000:00:03.0
PCI: Probing PCI hardware done
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
matroxfb: Matrox G450 detected
matroxfb: 640x480x8bpp (virtual: 640x26214)
matroxfb: framebuffer at 0x3FDC0000000, mapped to 0xe000000080004000, size 33554
432
fb0: MATROX frame buffer device
fb0: initializing hardware
Using unsupported 640x480 MTRX,G450 at e0000000, depth=8, pitch=640
fb1: Open Firmware frame buffer device on /pci@400000000111/pci@2/pci@1/display@
0
RTAS daemon started
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
Console: switching to colour frame buffer device 80x30
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS2 at I/O 0x890 (irq = 15) is a 16550A
ttyS3 at I/O 0x898 (irq = 14) is a 16550A
Using anticipatory io scheduler
Floppy drive(s): fd0 is 2.88M
FDC 0 is a National Semiconductor PC87306
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
pcnet32.c:v1.30c 05.25.2004 tsbogend@alpha.franken.de
e100: Intel(R) PRO/100 Network Driver, 3.0.18
e100: Copyright(c) 1999-2004 Intel Corporation
e100: eth0: e100_probe: addr 0x3fd88030000, irq 101, MAC addr 00:02:55:4F:58:8B
e100: eth1: e100_probe: addr 0x3fdec030000, irq 137, MAC addr 00:02:55:AF:8E:73
netconsole: not configured, aborting
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
W82C105: IDE controller at PCI slot 0000:00:03.1
W82C105: chipset revision 5
W82C105: 100% native mode on irq 102
    ide0: BM-DMA at 0xf040-0xf047, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf048-0xf04f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide0...
Probing IDE interface ide1...
sym0: <1010-66> rev 0x1 at pci 0000:41:01.0 irq 103
sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18j
sym0:8: FAST-40 WIDE SCSI 80.0 MB/s ST (25.0 ns, offset 31)
  Vendor: IBM       Model: ST336605LC        Rev: C50B
  Type:   Direct-Access                      ANSI SCSI revision: 03
sym0:8:0: tagged command queuing enabled, command queue depth 16.
scsi(0:0:8:0): Beginning Domain Validation
sym0:8: asynchronous.
sym0:8: wide asynchronous.
sym0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
scsi(0:0:8:0): Ending Domain Validation
sym0:9: FAST-40 WIDE SCSI 80.0 MB/s ST (25.0 ns, offset 31)
  Vendor: IBM       Model: ST336605LC        Rev: C50B
  Type:   Direct-Access                      ANSI SCSI revision: 03
sym0:9:0: tagged command queuing enabled, command queue depth 16.
scsi(0:0:9:0): Beginning Domain Validation
sym0:9: asynchronous.
sym0:9: wide asynchronous.
sym0:9: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
scsi(0:0:9:0): Ending Domain Validation
  Vendor: IBM       Model: HSBPD4E  PU3SCSI  Rev: 0015
  Type:   Enclosure                          ANSI SCSI revision: 02
scsi(0:0:15:0): Beginning Domain Validation
sym0:15:0:phase change 6-7 6@60050390 resid=4.
scsi(0:0:15:0): Ending Domain Validation
sym1: <1010-66> rev 0x1 at pci 0000:41:01.1 irq 104
sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.1.18j
sym2: <875> rev 0x3 at pci 0001:21:01.0 irq 117
sym2: No NVRAM, ID 7, Fast-20, SE, parity checking
sym2: SCSI BUS has been reset.
scsi2 : sym-2.1.18j
sym2:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 16)
  Vendor: HP        Model: IBM-C568303030!D  Rev: C209
  Type:   Sequential-Access                  ANSI SCSI revision: 02
scsi(2:0:0:0): Beginning Domain Validation
sym2:0: FAST-20 SCSI 20.0 MB/s ST (50.0 ns, offset 16)
sym2:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 16)
scsi(2:0:0:0): Domain Validation skipping write tests
scsi(2:0:0:0): Ending Domain Validation
  Vendor: IBM       Model: DVRM00203     !K  Rev: A132
  Type:   CD-ROM                             ANSI SCSI revision: 02
scsi(2:0:1:0): Beginning Domain Validation
sym2:1: FAST-10 SCSI 10.0 MB/s ST (100.0 ns, offset 16)
scsi(2:0:1:0): Domain Validation skipping write tests
scsi(2:0:1:0): Ending Domain Validation
ipr: IBM Power RAID SCSI Device Driver version: 2.0.7 (May 21, 2004)
st: Version 20040403, fixed bufsize 32768, s/g segs 256
Attached scsi tape st0 at scsi2, channel 0, id 0, lun 0
st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 393216
SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
 sda: sda2 sda3 sda4
Attached scsi disk sda at scsi0, channel 0, id 8, lun 0
SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sdb: drive cache: write through
 sdb: unknown partition table
Attached scsi disk sdb at scsi0, channel 0, id 9, lun 0
sr0: scsi3-mmc drive: 0x/0x dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
Attached scsi generic sg0 at scsi0, channel 0, id 8, lun 0,  type 0
Attached scsi generic sg1 at scsi0, channel 0, id 9, lun 0,  type 0
Attached scsi generic sg2 at scsi0, channel 0, id 15, lun 0,  type 13
Attached scsi generic sg3 at scsi2, channel 0, id 0, lun 0,  type 1
Attached scsi generic sg4 at scsi2, channel 0, id 1, lun 0,  type 5
matroxfb_crtc2: secondary head of fb0 was registered as fb2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
input: PS/2 Logitech Mouse on isa0060/serio1
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Raw Set 2 keyboard on isa0060/serio0
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
   8regs     :  4368.000 MB/sec
   8regs_prefetch:  3752.000 MB/sec
   32regs    :  4516.000 MB/sec
   32regs_prefetch:  3992.000 MB/sec
raid5: using function: 32regs (4516.000 MB/sec)
raid6: int64x1    847 MB/s
raid6: int64x2   1207 MB/s
raid6: int64x4   1265 MB/s
raid6: int64x8   1199 MB/s
raid6: using algorithm int64x4 (1265 MB/s)
md: raid6 personality registered as nr 8
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
oprofile: using ppc64/power4 performance monitoring.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 128Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
IPv4 over IPv4 tunneling driver
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Kernel panic: VFS: Unable to mount root fs on sda2


Tags: untagged
Subscribe
  • Post a new comment

    Error

    Anonymous comments are disabled in this journal

    default userpic

    Your reply will be screened

    Your IP address will be recorded 

  • 0 comments